Aggregate Testing Equipment

Product Details:

Los Angeles Abrasion Testing Machine is used for testing crushed slag, crushed and uncrushed gravel for resistance to abrasion. The aim of the test is to find the percentage wear due to the relative rubbing action between the aggregates and steel balls as abrasive charge. The oven-dried arrangements are weighted and rotated along with abrasive charge in the machine for the 500 or 1000 revolutions and percentage of wear so found out its reported as los angeles abrasion value.

Model Overview:

• Consists of a hollow steel cylinder, closed at both ends, having an inside diameter of 700 mm and inside length of 500 mm.
• The cylinder mounted on a sturdy frame on ball bearings. The opening is closed dust tight with a removable bolted cover in place.
• A detachable shelf which extends through the drum catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated at a speed of 30-33 rpm by an electric motor through a heavy duty reduction gear.
• Fitted with revolution counter and push button starter. Supplied complete with a tray for collection of the material. Abrasive charge consists of set of 12 nos.
• Cast iron spheres or steel spheres (hardened steel balls) approximately 48mm diameter each weigh between 390-445 gram. Complete as above.

Note - Price will be change as per specification

Product Details:

Complete with a cylindrical cup, 102 mm dia X 50 mm depth, one measure 75 mm dia X 50 mm deep and a tamping rod of circular cross section 10 mm in diameter and 230 mm long, rounded at one end. AS PER IS: 2386 (Part - IV)/ IS 9377

Also We Have Aggregate Impact Testing Machine With Blow Counter- 

Note - Price will be change as per specification

 

 

Product Details:

Compliance with following International Standards

 IS : 1199, IS : 10079, BS : 1881, ASTM C29

Also we have manufacturer

• BULK DENSITY CYLINDERICAL METAL MEASURE (ISI)-3 LTR.
• BULK DENSITY CYLINDERICAL METAL MEASURE (ISI)-15 LTR.
• BULK DENSITY CYLINDERICAL METAL MEASURE (ISI)-30 LTR.

Note :- Price will be change as per specification

Product Details:

Impact Value Testing Machine provides a relative measure of the resistance of an aggregate to sudden shock or impact. The oven dried and accurately weighed aggregates are subjected to a total of 15 blows of specified weight and fall and percentage of fines formed in terms of the total weight of the sample is expressed as the aggregate impact value.

Specifications:

• Consists of base weighing between 20-30 kg with a lower surface of not less than 30cm and support columns to form a rigid frame work around the quick release trigger mechanism to ensure an effective free fall of the hammer during test. The free fall can be adjusted through 380 5.0 mm. The hammer is provided with a locking arrangement. A metal tup (hammer) weighing 13.5 to 14.0 kg, the lower end of in cylinderical shape, 100 mm in diameter and 5 cm long with a 2mm chamfer at the lower edge and case hardened. Complete with a cylindrical cup, 102 mm dia x 50 mm depth, one measure 75 mm dia x 50 mm deep and a tamping rod of circular cross section 10 mm in diameter and 230 mm long, rounded at one end.

Optional Accessories:

• Test Sieve 10 mm, 12.5 mm and 2.36 mm opening.
• Laboratory Oven.
• Automatic Blow Counter.
• Electronic Balance 500 gm x 100 mg/ Two Pan Balance

Note - Price will be change as per specification

Product Details:

Aggregate Crushing Value Apparatus provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. The oven dried and accurately weighed aggregates are subjected to crushing test on compression testing machine and weight of the resultant fines passing the specified IS sieve to the total weight of the sample expressed a s a percentage is defined as Aggregate Crushing Value. The apparatus is available in three size 75mm dia for 1/8” to ¼” size aggregate, 150mm dia for 3/8” to ¾” aggregate (standard) and 300mm dia for 1” to 2” aggregate.

Specification:

• Consists of Case hardened Mild steel cylindrical container of 150 mm dia 0.5 mm x 130 mm to 140mm high with base plate 200 to 230 mm square x 6mm thick.
• A plunger of 148 mm 0.5 mm dia x 100 to 115 mm high.
• All parts directly coming in to contact with the specimen during the test are made of mild steel duly case hardened.
• Supplied complete with tamping rod, 16 mm dia x 600 mm long, one end rounded.

Optional Accessories:

• Cylinderical Metal measure 11.5 cm dia x 18 cm height with handle.
• Electronic Balance 3 kg. X 1 gm
• Compression Testing Machine Capacity : 500 kN
• Test Sieve 2.36 mm, 10 mm, 12.5 mm and 14 m

Note - Price will be change as per specification

Product Details:

Buoyancy Balance consists of a rigid support frame,incorporating a water tank mounted on a platform. A mechanical lifting device is used to raise the water tank through the frame height immersing the specimen suspended below the balance. The balance supplied may also be used as a standard weighing device, thus providing a versatile and comprehensive weighing system in the laboratory.

Specifications:

Note - Price will be change as per specification

Product Details:

Sieve Shaker Gyratory is designed to carry up to 7 sieves of 6 inch or 8 inch diameter. The 12 inch diameter sieves can be used with the help of adaptor. A 1/4 HP. motor through a reduction gear immersed in oil drives the shaker. The sieve table dies not rotate but is inclined from the vertical axis and the direction of inclination changes progressively in clockwise direction. If the stop-pin below the table is removed. the shaker can have a rotary motion. In addition to this gyratory motion of the table, there is an upward and downward movement ensuring that each square cm of the sieve is utilized. A pair of rods and a holder is supplied. The holder can be fixed on the top of the upper most sieves, and thus the sieve set is firmly held. Suitable for operation on 230 volts, 50 cycles single phase A.C Supply. Adaptor for 30cm dia test sieves can be fitted in above.

Specifications:

• For 45Cm Dia Sieves: This sieve shaker is designed to carry up to 7 sieves of 18" diameter. The shaker is driven by a 1/2 H.P.Electric Motor through a reduction gear. The sieve table does not rotate but is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction, in addition to this gyratory motion of the table, there is and upward and downward movement at a frequency of about 270 vibration per minutes ensuring that each square inch of the sieve is utilised. The whole gear mechanism runs in an oil bath, without test sieves or time switch. Suitable for operation from 220 Volts 50 cycles A.C. supply.

Optional Extra:

• Digital Time switch 0-99 minutes for above
• Mechanical Time switch 0-60 minutes for above

Optional Extra:

• Digital Time switch 0-99 minutes for above
• Mechanical Time switch 0-60 minutes for above

Salient Features

• Carries upto 7 sieves of 200mm diameter in single adaptor.
• The shaker is driven by a 1/4 HP motor through a reduction gear.
• A pair of rods and holders is supplied along with the main unit.
• The holder can be fixed on top of the upper most sieves, and thus the sieve set is firmly held.
• Suitable for operation on 230 volts, 50 cycles single phase A.C. Supply.
• Fitted with Digital adjustable timer
• No. of tapping from bottom : 85 to 90
• Timer : Digital Pre-settable timer
• Timer Range : 0 to 99 Minutes

Note - Price will be change as per specification

Additional Information:

• Item Code: EIE-TM157-158

Product Details:

Applications

To speed crushing process of aggregate, iron ores, minerals, coals, coke, chemicals and other similar materials

Construction Details

• Compact and Rugged construction
• Identical choice for general laboratory or small pilot plant
• Easy cleaning & Maintenance
• Extremely fast & efficient primary crushing
• Two jaws of manganese steel are provided in the jaw crusher.
• Moveable jaw produces two blows for every revolution, thus reducing over sizing to a minimum.
• Combination of forward and downward strokes with a rocking action exerts pressure on the coarse material to pass through the jaws.
• Fitted with hopper at the top for feeding materials.
• Smooth jaws ensure a uniform product output
• Start & Stop push button, overload protection for motor

Note - Price will be change as per specification

Additional Information:

• Item Code: EIE-TM87

Product Details:

The flakiness index is the total weight of the material passing the various thickness gauges or sieves, expressed as a percentage of the total weight of the sample gauged. Compliance with IS : 2386 (PART-1) It consists of a frame with sliding panel. The panel has slots of different standard length and width accurately cut.

Also we have flakiness gauge - m.s. Chromepowder coated

Note - Price will be change as per specification

Product Details:

Complies with following International StandardsIS : 2386 (PART-1)
PurposeThis instrument is used to determine the elongation index of aggregates. Particle is elongated when its length (longest dimension) is more than 1.8 of the midsize of the sieve fraction.
Significance & UseThis method classifies aggregate elongation by measuring the length of individual particles. The test is not applicable to material retained on a 63.0 mm BS test sieve.
Construction Details

• Consists of a hard wood base with vertically mounted metal studs 
• Eight metal studs are mounted.
• Aggregate to be classified is separated into seven sieve fractions from 63 to 6.3mm, and each fraction is examined separately.
• The mass of all elongated particles (failing to pass between pins) as percent of the sample is the elongation index.
• The distance between nails is applied according to following table.

 Distance between nails (mm)      Passing/Retained (mm)                  -----                                       63/50                  81.0                                        50/40                  58.5                                        40/31.5                  -----                                       31.5/25                  40.5                                        25/20                  32.4                                        20/16                  25.6                                        16/12.5                  20.2                                        12.5/10                  14.7                                        10/6.3

Also We Have Length Gauge (Elongation Gauge)

Note : Price will be change as per specification

Additional Information:

• Item Code: TM-104-ISI
• Production Capacity: 500 per annum
• Delivery Time: 3-4 Weeks after receipt of confirmed order
• Packaging Details: Wooden packing with strong base.

Product Details:

Also We Have Manufacturer

• Bulk density cylinderical metal measure-20 ltr.
• Bulk density cylinderical metal measure-15 ltr.
• Bulk density cylinderical metal measure-10 ltr.

Note - Price will be change as per specification

Product Details:

Cone and Tamper Sand Absorption is used for specific gravity and absorption of fine aggregates.

Specifications:

• The equipment comprises of a conical metal mould 1.5” dia at the top, 3.5” dia at the base and 2.7/8” in height and a metal tamping rod weighing 12 ounces and having a flat circular tamping face 1” dia.
• Packing: standard export packages
• Port: Tianjin
• Production Capacity: 2000 sets/month

Note - Price will be change as per specification