EIE Instruments Private Limited

Compliance With Following National / International Standards:

ASTM D4491, IS 14324, EN ISO 11058

These test methods cover procedures for determining the hydraulic conductivity (water permeability) of Geo‑Textiles in terms of permittivity under standard testing conditions, in the uncompressed state.

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards:

ISO 13427, ASTM D4886, IS 14714, Annex B of IS 16653


Geotextile Abrasion Resistance Tester is used to determine the resistance of geotextile or geotextile-related products to abrasion using an abrasion tester by Sand Paper/Sliding Block Method. It is only applicable to geotextile.

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards:

ASTM D5199, IS 13162 (Part-3), IS 2508


Suitable to measure Thickness of Geotextile, Geocomposite, Geonets, HDPE Geomembrane & Geomembrane material.

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Applications:

• Geo-synthetic material including Geo-textile, Composite Geo-textile, Geo-grid, Geo-membrane, Geo-Net etc. Which are used in traffic, water conservancy, tunnel, building construction and other industries.
• Suitable to conduct Grab, Puncture, Tearing, CBR Push through, wide width tensile tests confirming to procedure laid down in ASTM Standards

Salient Features:

• Equipped with Twin (Dual) Load cells to carry out various Geo-textile tests, Geo-Membrane tests within the capacity range
• Equipped with wide variety of grips for different test samples as per above listed ASTM Standards
• Equipped with Servo Motor, Servo drive and dedicated colour LCD Touch graphic controller for Automatic operations
• Auto Load rate/Strain rate control using Imported servo/proportional Valve
• Smooth and accurate load rate control
• Easy load cell selection only by easy to handle change over switch
• Both Load-cell are permanently mounted, no need to remove any load cell for different-different tests
• Overload & extension protection parameter for mechanical safety by help of limit switches
• Also fitted with Emergency stop button to test the stop in between
• Automatic electronic controllable movement of Cross-head travels (START-STOP-UP-DOWN) with the help of LCD Touch screen and Dedicated Software - both
• Auto-stop / Return of cross heads to home position as and when sample breaks
• Speed Variation by dedicated Servo Drive from 0.01 mm/min to 500 mm/min
• Extension indication with least count of 0.5 mm through Proximity switch
• Supplied with Dedicated UTM Software to carry our various operation of the machine through software itself, User can also log and modify the recorded data, An operator can also plot various online graphs i.e. stress vs strain, Stress vs Time, Strain Vs Time within the software itself
• User can also export the generated data to excel files for further analysis
• Also, Supplied complete with Instruction manual, Test report and calibration certificate

Specifications:

• Motor Speed range : From 0.01mm/min to 500 mm/min
• Motor speed variation : With the help of dedicated Servo Drive
• Horizontal clearance : 350 - 400 mm
• Vertical Clearance : 600 - 700 mm
• Total cross head travel : 700 mm
• Position resolution : 0.01 mm
• No of load cells : 02 Nos
• Load cells capacity : 3 KN and 30 KN
• Load cell least count : 0.01 KN and 0.1 KN respectively
• Encoder : For elongation indication, 2500 PPR
• Elongation Least count : 0.5 mm travel
• Unit selection : Newton / Kgf / KN
• Display : 7” Touch screen Digital Display from Reputed brand
• Indication Parameters : Maximum Load, Maximum Elongation, Selected Load Cell, Breaking Load, %Elongation, Current Load
• Paint : Powder coating in attractive shades
• Operates on : 415 Volts, 50 Hz, Single Phase, AC Supply
• Type : Floor standing Universal Testing Model

Note - Price will be change as per specification 

Compliance With Following National / International Standards:

ASTM D4533, ASTM D4595, ASTM D4632, ASTM D4833, ASTM D6241, ISO 12236, ISO 10319, IS 14293

Applications:

 

• Geo-synthetic material including Geo-textile, Composite Geo-textile, Geo-grid, Geo-membrane, Geo-Net etc. Which are used in traffic, water conservancy, tunnel, building construction and other industries.
• Suitable to conduct Grab, Static Puncture (CBR Puncture), Index puncture, Trapezoid Tear and wide width tensile tests confirming to procedure laid down in above listed ASTM Standards

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards:

ASTM D882, ASTM D828, ASTM D1938, ASTM D1876, ASTM D638, ASTM F88, ASTM F904, ASTM D2256, ASTM D5034, ASTM D412, ISO 1924, TAPPI T494

EIE Make ‑ Computerized Tensile Strength testing machine having capacity of 0‑1000 Kgf (10 KN) (10000 N). Supplied complete with dedicated PC software program. Equipped with Ball screw, Induction motor & Motor Drive (for speed variation 10mm ‑ 350mm/min) along with encoder to measure the elongation using Pair of Grips.

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards:

ASTM D4751, BS 6906 (Part 2), IS 14294, EN ISO 12956

A Geo-Textile specimen is placed in a sieve frame, and sized glass beads are placed on the Geo-Textile surface. The Geo-Textile and frame are shaken laterally so that the jarring motion will induce the beads to pass through the test specimen. The procedure is repeated on the same specimen with various size glass beads until its apparent opening size has been determined.

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards

EN ISO 13433 (2006), BS 6906 (Part 6), EN 918

Mainly used to measure the puncture strength as well as the fabric quality to withstand aggregate penetration. 

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.