EIE Instruments Private Limited

Compliance with following International Standards

ASTM D1401

Compliance With Following National / International Standards:

ASTM D92, IP -36/57

This apparatus is used for determination of Flash Point of petroleum products except fuel oil with open flash 80°C as per specification IP 36/57, IS 1448 (P:69) 1969 and ASTM-D-92.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

Compliance with following International Standards:

ASTM D-566, IP-132, ISO-2176

Purpose:

This test method covers the determination of the dropping point of lubricating grease. This test method is not recommended for use at bath temperatures above 288°C.

Significance & Use:

In general, the dropping point is the temperature at which the grease passes from a semisolid to a liquid state under the conditions of test. This change in state is typical of greases containing as thickeners soaps of conventional types. This test method is useful to assist in identifying the grease as to type and for establishing and maintaining bench marks for quality control.

Also available in various types of operations and models such as : 1) Hand Operated 2) Motorized Stirrer with Electrical Heating and 3) Magnetic Stirrer cum Heater.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

IP 53, ASTM D473, IS 1448 (P‑30)

Operating Procedure:

The sample is placed in a refractory thimble and washed with condensed toluene vapors leaving only insoluble matter, the residue is calculated as a percentage of the total mass.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

• Model: Single Tank, Floor model with castor wheels
• Tank designed to accommodate 4 Test jars at a time.
• Inner tank made of 304 grade stainless steel
• Outer body is fabricated of mild steel with powder coated.
• The top surface made stainless steel with white Teflon sheet lid
• Digital temperature display with resolution of 0.1°C
• Long life, high safety zone, stainless steel immersion heaters
• Automatic low liquid level safety cut-off & drain to empty tank almost fully
• Stirrer will be provided for uniform cooling throughout the Bath.
• Seamless copper jackets, with disks, gaskets, test jars, corks.

Compliance With Following National / International Standards:

1448(P:20) 2019, IP‑33,170,ISO 13736:2013, ISO 15528

Applications : Used for Educational Experimental Purpose Only

Used for determination of the closed cup Flash Point of Petroleum products, their mixtures, other liquids and paints having flash point below 70°C. 

Also availabe in various models such as : 1) With Energy Regulator and 2) Digital Temperature Indicator

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

ASTM D2272, ASTM D2112, IP 229

These methods used to evaluate the oxidation stability of new and in‑service engine, turbine and inhibited mineral insulating oils in the presence of water and a copper catalyst coil at 150°C as per ASTM D2272 and at 140 °C test temperature as per ASTM D2112. The method is applicable to determine the oxidation stability of both ‑ steam turbine oil and inhibited mineral insulating oil

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards:


ASTM D482, IP 04


This test method covers the determination of ash in the range 0.001- 0.180 mass %, from distillate and residual fuels, gas turbine fuels, crude oils, lubricating oils, waxes, and other petroleum products, in which any ash-forming materials present are normally considered to be undesirable impurities or contaminants.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

This Multiple Redwood viscometer is designed for viscosity tests of petroleum Products. It consists, One Red Wood No.1 cup and One Red Wood No. 2 cup are installed in the bath

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

ASTM D6371, IP 309, IS 1448 Part 110

Purpose:

Used for Determination of the cold filter plugging point (CFPP) temperature of diesel and domestic heating fuels by measuring the temperature at which the sample ceases to flow through a wire mesh filter.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

• Cone penetration tests not only evaluates the consistency of Lubricating Grease over the full range of NLGI Numbers from 000 to 6, but also evaluates the consistency of stiff greases having penetration number less than 85.

• Compact design and rugged construction ensures long service life and facilitates transport for field applications.
• Powder coated body parts for aesthetical outer appearance
• Sturdy cast iron base provides excellent support.
• Built-in spirit level and leveling screws ensure proper alignment during testing.
• Supplied with Cone, container, weight and Digital time controller·
• The penetration time is controlled and indicated on Digital Timer Panel with least count of 0.1 second.
• The automatic digital timer and electrical arrangement, which on push of a button, allows the plunger rod to fall freely for 5 seconds and clamps it automatically after 5 seconds.
• The penetration value is measured and indicated on dial gauge.
• Dial Gauge measures the penetration distance in 1/10th mm accuracy.
• Operates on 230 Volt, 50 Hz, Single Phase, AC Supply

• Digital time controller with auto magnetic clutch release mechanism on push of a button. Having timing range 0-99 minutes (No need of stop watch) - 1 No
• Sample container of 100mm dia x 100mm height - 1 No
• Transfer dish - 1 No
• Penetrometer Hollow 90° brass cone, Highly polished stainless steel tip - 2 Nos
• Magnetic coil for automatic controller - 1 No

• Item Name: Grease Penetrometer
• Reference Standard: ASTM D5, ASTM D217, ASTM D937
• Usage: ASTM D217 Grease Cone Penetrometer
• Test Samples: Oil, Grease, Wax, Asphalt, etc.
• Max. Penetration: 600

Complies with following International Standards

Compliance With Following National / International Standards:

IP 24, IP 123, ASTM D‑86

Application

This apparatus is used for determinations of distillation characteristics of petroleum products.

Also available in Refrigerated OR Non Refrigerated Model. 


Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

ASTM D2272, ASTM D2112, IS 12958, IP 229

Also available in various types of operation such as : 1) With Pressure Gauge System and 2) Electronic System with PC Aoftware

These methods used to evaluate the oxidation stability of new and in‑service engine, turbine and inhibited mineral insulating oils in the presence of water and a copper catalyst coil at 150°C as per ASTM D2272 and at 140 °C test temperature as per ASTM D211

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards:

ASTM D892, IP 146, ISO 6247


Supplied with single test cylinders and single jar. Air flow meter and diffuser ball. Supplied with cooling coil. 

Further details available on our website.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance with following International Standards:

ASTM D381, IP 131, IP 540


This test method covers the determination of the existent gum content of aviation fuels, and the gum content of motor gasoline or other volatile distillates in their finished form, (including those containing alcohol and ether type oxygenates and deposit control additives) at the time of test.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

Compliance With Following National / International Standards:

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards:

• 1000ml capacity
• Conforms to ASTM D473
• Stainless steel basket supporting an extraction thimble of alundum

Compliance With Following National / International Standards:

Applications:

Used for determination of the closed cup Flash Point of Petroleum products, their mixtures, other liquids and paints having flash point below 70°C. 

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:


IP 69, IS 1448 (P:39), ASTM D323, ASTM D1267


Used to determine the vapour pressure of volatile non???viscous petroleum products except liquefied petroleum gases.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

Compliance With Following National / International Standards:


ASTM D611, IP 2

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

D445, IS 1448 (P 25)

Purpose :

• To find out kinematic viscosity of Petroleum products at Ultra Low Temperature values.
• Used as a Constant Temperature Bath in crystal growth.
• General purpose constant temperature bath
• Can also be used for other low temperature tests such as Freezing Point, Cloud Point, Pour Point

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

• Tactfully designed
• Aesthetical Appearance
• Easy to clean and operate
• User friendly operating features
• Exterior body powder coated in attractive shades
• Highly accurate and reliable results
• Major customers - Indian Oil, Bharat Petroleum

Specifications:

• Motor: Servo Motor

Compliance With Following National / International Standards:

IP 13, ASTM D189, ASTM D2416

It is used to determine the amount of carbon deposit, when oil is evaporated under specified condition. The Carbon Residue values of crude oil, residue etc. are useful in the manufacturimg of various lubricants. 

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

Compliance With Following National / International Standards:

Further details available on our website.

Price and specifications mentioned here are subject to change as per the application, customer requirements and prevailing market conditions. Please refer to us for the final rates and offer.

Compliance With Following National / International Standards:

Compliance With Following National / International Standards:

Applications:

Used for estimation of moisture in lubricating oil as per with one 10 cc (ml) receiver fitted with stop cock, 1000 ml Round Bottom Flask & clamp with stand. Complete with Heating unit

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user. 

Compliance With Following National / International Standards:

ASTM D1742


This test method covers the determination of the tendency of lubricating grease to separate oil during storage in both normally filled and partially filled containers. 

Further details available on our website.

Compliance With Following National / International Standards:

IP-57 & IS - 1448 (P:32) & ASTM-D-1322

This method describe a procedure for evaluating a kerosine without producing smoke.

• Used for evaluating illuminating oils in respect of their ability to burn without smoke.
• The apparatus consists essentially of four parts lamp body, candle socket, candle and tripod stand. The candle may be raised or lowered by a micrometer screw arrangement. The size of the flame may be measured on a blue scale with white markings 0 to 50 mm.

Further details available on our website.

The Price mentioned here are subject to change as per the capacity, specifications and application of the user.