Bitumen Testing Equipment

Product Details:

Other Details:

• Used to maintain in water the Marshal specimens to be tested at 600 10 (Asphalt specimens) or 37.80 (Tar Specimens) as prescribed by the specifications.
• The Same Water bath can also be used for Penetration test, Stripping test or even soundness test of cement with the use of additional accessories. Available in different sizes and temperature control system.

Specifications:

• Temperature range from ambient to 100^oC and temperature controlled by digital temp. Indicator cum controller with an accuracy of + 0.5^oC.
• A high speed stirrer with a motor of 1/20 HP is fitted to the unit for continuous stirring and this can maintain a uniform heating throughout the chamber.
• The heating mechanism comprises of set of heaters pertaining to fast heating to operate 230 volts AC only.

Constant Temperature waterbath Digital Model Selection Guide

Constant Temperature waterbath Themostatic Model Selection Guide

Chamber size (W x D x H)	Chamber capacity (Liters)	Digital Model Numbers (EIE-406EP)	Digital GMP Model Numbers (EIE-406EG)
30 x 15 x 15 cm	7	EIE-406EP7	EIE-406EG7
35 x 15 x 15 cm	8	EIE-406EP8	EIE-406EG8
25 x 20 x 20 cm	10	EIE-406EP10	EIE-406EG10
30 x 25 x 20 cm	15	EIE-406EP15	EIE-406EG15
25 X 25 X 25 cm	16	EIE-406EP16	EIE-406EG16
35 x 30 x 17.5 cm	18	EIE-406EP18	EIE-406EG18
45 x 30 x 17.5 cm	24	EIE-406EP24	EIE-406EG24
45 X 30 X 25 cm	34	EIE-406EP34	EIE-406EG34
45 x 35 x 30 cm	47	EIE-406EP47	EIE-406EG47
50 x 35 x 30 cm	52	EIE-406EP52	EIE-406EG52
50 x 60 x 35 cm	105	EIE-406EP105	EIE-406EG105

Note - Price will be change as per specification

Product Details:

The following testing equipment are used to measure.

Absolute Kinematic Viscosity Bath graded paving bitumen (IS:73:2006) at 60°C in accordance with IS:1206 (Part II) (similar to ASTM D 2171), which uses a vacuum capillary viscometer. It may please be noted that any other viscometer such as rotational viscometer cannot be used to measure the absolute viscosity at 60°C since the bitumen in non Newtonian in nature at this temperature.

Specifications:

• Complete Absolute Viscosity Testing Equipment conforming to IS: 1206 (Part II) Method for Testing Tar and Bitumen Materials: Determination of Absolute Viscosity with the following components:
• Constant Temperature Bath: A suitable bath for immersion of at least 2 vacuum capillary viscometer tubes with a digital temperature controller. The accuracy of the temperature in the bath will be ± 0.1°C throughout the bath.
• Vacuum System: Capable of maintaining a vacuum within ± 0.05 cm of the desired level The system will consist of vacuum pump, moisture trap, vacuum regulator, bleed valve, all interconnecting tubing/ piping, and any other accessory as needed to complete the vacuum system.
• Thermometer for Bath: Mercury in glass, range 37.8 to 82°C, and graduations of 0.2°C.
• Timing Device: A stop watch or stop clock capable of reading up to ½ second.
• Cannon-Manning Vacuum Viscometers: With manufacturers' calibration certificate, viscometer holder and silicone cork. Size 12 and Size 13 (one each) [Size 12 is suitable for testing VG-10 and Size 13 is suitable for testing VG-20, VG-30, and VG-40 bitumen.

Note - Price will be change as per specification

Product Details:

Also we have compaction pedestal - 6"

Note - Price will be change as per specification

Product Details:

Compliance Standards

ASTM D6307-98 and AASHTO T308.

Introduction

The Asphalt Content/Binder Furnace with internal automatic balance is an environmentally-friendly and cost-effective method for the accurate determination of asphalt content. Ignition method reduces testing time compared to solvent testing methods and automatic operation frees technicians for other tasks. Accurate internal balance monitors weights automatically throughout ignition. Easy operation- simply enter sample weight, calibration factor, load the sample, and push start, when unit beeps at test end, push stop, and sign receipt. 

Note - Price will be change as per specification

Product Details:

Ring and Ball Apparatus is meant for determination of softening point of bituminous materials according to IP 58 and IS 1205 Softening point is that temp. at which the specimen under test becomes soft enough to allow a steel ball of specific dimension to fall a required distance under test condition.

Note - Price will be change as per specification

Product Details:

As per ASTM D 88. The apparatus consists of stainless steel bath with oil cup which is centrally placed in a water bath. The bath has a lid which contains a water cooling tube, two handles with two stirring blades, thermometer socket and a straight heater. Stirring is done by turntable arrangement. A thermometer can also be inserted into the cup cover. Two jets one universal and one furol can be screwed to the cup by a handle (without strainer, withdrawal tube and glass wares) To work on 220V AC single phase. Temperature control by separate energy regulator.

Other accessories Viz. ASTM / IP Thermometers, Flask receiver 60 ml, Digital stopwatch and consumable spares will be available at extra cost.

Note - Price will change as per specification

Additional Information:

• Item Code: EIE-TM48

Product Details:

Salient Features

• Aesthetic exterior appearance
• Reliable and sturdy construction
• Reduces testing time and cost
• Eliminates exposure to harmful solvents (Environmental friendly operation)
• Fully automatic test cycle, which frees technician for other tasks.
• Magnetic door lock system to avoid sudden accident
• Integrated weighing system monitors sample weight with high precision
• Automatic printout of test result at end of test
• 7” Touch screen HMI & PLC Controller
• Allows easy navigation of parameter setting, Debugging and Calibration

Technical Specifications

Note - Price will be change as per specification

Product Details:

Digital Model complying to ASTM D402 Standard with all required testing accessories.

Compliance Standards

ASTM D402, IS 1213, IP - 27

Note : Price will be change as per specification

Product Details:

Introduction:

• This Equipment is to speed up the process with ease and accuracy to prepare cylindrical specimens for Marshal Stability Testing Machine. The compactor has been designed to simulate hand compaction as described in ASTM D1559. This apparatus automatically compacts the sample and stops after preset number of blows has been completed. The Compactor gives Uniformly and accurately compacted marshal moulds for reliable testing.

Specification:

• It is a motor driven mechanical compactor useful for compaction into 100 mm dia moulds.
• It is fitted with a compaction rammer of 98.5mm dia, weighing 4.535 kg. with a free fall of 457 mm.
• The rammer assembly is provided with a ratchet and pawl arrangement to lift it from the top of the test sample. When the rammer reaches the required height the pawl release the rammer which falls freely on test specimen. The release mechanism is connected by an arm moving up and down which is connected to a reduction gear coupled to the motor through another arm. An automatic blow counter fitted to the compactor is used to set the number of blows.
• The Compactor is supplied complete with wooden pedestal. Suitable to work on 220V, 50 Hz, AC single phase.

Low temperature waterbath Model Selection Guide

Price will be change as per specification

Product Details:

Details

The apparatus will be used to measure the resistance to plastic flow of cylindrical specimen of bituminous paving mixture loaded on the lateral surface. The apparatus will be used for mixtures containing asphalt cement and aggregate up to 37.5 mm nominal maximum size. 

Supplied complete with  following accessories 

• Three specimen moulds, cylindrical 6" dia.
• Three base plate.
• Three collars 6.1/8" dia.
• Two compactions hammers, 10.2kg weight and 47.7cm drop.
• One specimen extractor.
• One compaction pedestal complete with specimen holder
• One breaking head assembly, complete with gauge disc and flowmeter pedestal.
• One loading transfer bar.
• 100 KN capacity Loading unit motorised with uniform vertical movement of 5.08cm/min. Suitable for  operation on 230 volts AC supply. With limit switch to restrict over travel.
• Suitable for operation on 230 Volts, 50 Hz, AC supply. With limit switch to restrict over travel.
• One PROVING RING 5000 kg (50 KN) capacity fitted with calibration report
• One dial gauge 0.01mm X 25 mm travel.

Note - Price will be change as per specification

 

 

 

 

 

 

 

 

 

 

 

 

Additional Information:

• Item Code: EIE-TM-041

Product Details:

Model Overview:

• The unit is heavily insulated & has a double glass built in door for view inside temperature is controlled at 163'deg C #1'deg C. by means of a calibrated PID based Digital Temperature Indicator Controller.
• Inside platform rotated by external motor from 5 to 6 R.P.M. & 2 stainless steel pans are also provided to hold cups. (supplied without cups).
• Inner chamber made of stainless steel sheet of 304 grade & outer of mild steel sheet stoving painted. To work on 230 volts, AC 50 Hz supply.

Note - Price will be change as per specification

Product Details:

We are manufacturer of Fully automatic versatile penetrometer. These machines are in great demand nationally and internationally. Highly reliable and durable, testing equipment are available in a variety of sizes at customer friendly prices.

Note - Price will be change as per specification

Product Details:

We are manufacturer of Matic Asphalt Hardness Tester. These machines are in great demand nationally and internationally. Highly reliable and durable, testing equipment are available in a variety of sizes at customer friendly prices.

Note - Price will be change as per specification

Product Details:

We are manufacturer of Loss on Heating Test Oven.

Special features of Heating Test Oven:

• Forced air circulation by F.H.P. continuous duty Motor for uniform heat distribution.
• Dual display microprocessor based PID Digital Temp. Indicator cum controller with sensor in place of thermostat and thermometer.
• Dual display microprocessor based Auto tuning PID Digital Temp. Indicator cum controller with soak timer and sensor in place of thermostat and thermometer. (See features mentioned below)
• Programmable microprocessor based dual display digital temperature controller.
• Dual display Digital timer with alarm.

Note - Price will be change as per specification

Product Details:

Compliance Standards:

EN 12593, IS 9381

 

Applications:

Used for determining the breaking point of solid and semi-solid bitumen. The Fraas Breaking Point is the temperature at which bitumen first becomes brittle, as indicated by the appearance of cracks when a thin-film of the bitumen on a metal plaque is cooled and flexed in accordance with specified conditions.

 

Apparatus Details:

Consists of following parts and accessories

• 1 set of 10 disposable metal plates,
• 1 test tube,
• 1 Dewar cylinder,
• 1 stand,
• 1 rubber stopper and
• 1 thermometer (IP-42C) (-38°C to + 30°C), subdivisions 0,5°C 

Note : Price will be change as per specification

Product Details:

Specifications

Additional Information:

• Item Code: EIE-PACO-01

Product Details:

Also We Have Marshal Stability Testing Machine-Digital 4"  Dia With Pc Interface Software & Marshal Stability Testing Machine Modified-Digital 6"  Dia.

Note - Price will be change as per specification

Product Details:

Earth has plenty of jewels and pearls in her lap; bitumen is also one of them. It is usually considered as one of the primary ingredients for constructing highways, roads and buildings. The strength, bonding, shock absorbent power, smoothness and many other similar properties of earth is due to bitumen content, which is spreaded with its well calculated mix material throughout the pavement. If mix is designed properly then it assures robust & classic highways. At this juncture, we at EIE, humbly present our wide range of bitumen testing equipments, asphalt testing instruments, aggregate testing equipments to lessen your burden of creating progressive and prosperous nation.

EIE’s comprehensive range of bitumen testing equipments, asphalt testing instruments comprises of Ductility testing machine, Rolling thin film oven, Bitumen penetrometer, Kinematic viscosity bath, Marshall stability test apparatus, Automatic marshal compactor, waterbath for penetration test etc.

Note - Price will be change as per specification

Product Details:

Compliance Standards

Apparatus for Solubility without vacuum pump in Tri-chloro Ethylene as per IS 1216.

Note : Price will be change as per specification

Product Details:

Compliance Standards

ASTM D1559, AASHTO T245, EN 12697-10, ASTM D6926

Also We Have Marshal Mould-Modified-(6" Dia)

Note - Price will be change as per specification

 

Additional Information:

• Production Capacity: 400 Per Year
• Delivery Time: 2-3 Weeks after receipt of confirmed order
• Packaging Details: Plastic packing with strong base

Product Details:

Complies With Following International Standards
ASTM D2872;  AASHTO T240 ;  CNR N.54; EN 12607 - 1

Price will be change as per specification

 

Product Details:

SPECIAL MODEL WITH AC MOTOR AND DRIVE : This model facilitates precise speed control and vibration free smooth operation. Speed variation up to 3600 RPM. Complies with following International Standards - ASTM D 2172, AASHTO T 58, T 164.

Note - Price will be change as per specification

Product Details:

Complies with following International Standards

ASTM D 2172, AASHTO T 58, T 164

Note - Price will be change as per specification

 

Product Details:

We are manufacturer of Ductility Testing Machine.

Note - Price will be change as per specification

Product Details:

Features:

• Compact design and rugged construction ensures long service life and facilitates transport for field applications.
• Sturdy cast iron base provides excellent support.
• Built-in spirit level and leveling screws ensure proper alignment during testing.
• Supplied with Needle, container, weight and Digital time controller
• The automatic digital timer and electrical arrangement, which on push of a button, automatically releases the plunger with Needle by a magnetic device.
• The penetration value is measured and indicated on dial gauge.
• Dial Gauge measures the penetration distance in 1/10th mm accuracy

Supplied complete with following Accessories:

• Digital time controller with auto magnetic clutch release mechanism on push of a button. Having timing range 0-99 minutes (No need of stop watch). 1 No.
• Weight of 50 Grams 1 No.
• Penetration cup of 55mm diameter x 35mm height 1 No.
• Transfer dish 1 No.
• Penetrometer Needle 1 No.
• Thermometer ASTM 17C (+19 to 27 °C) 1 No.

Specifications:

• Rated Voltage: AC220V±10% 50Hz
• Applicable Standard: IP-170, ISO13736
• Flash Detection: PT100
• Ignition: Gas
• Heating: Electric Furnace

Note: - Price will be change as per specification

Product Details:

Specifications:

Note - Price will be change as per specification

Product Details:

The machine is primarily intended to drill out core samples from the Asphalt or concrete road, Suitable for vertical drilling only.

Note - Price will be change as per specification

Product Details:

We are manufacturer of Bankleman Beam Apparatus.

Specifications:

• Benkelman Beam: Beam Ratio: 2 : 1
• Length of the probe arm from pivot to probe point 244 cm.
• Length of measurement arm from pivot to dial 122 cm.
• Distance form pivot to front legs 25 cm.
• Distance from pivot to rear legs 166 cm and
• Lateral spacing of front support legs 33 cm.

Other Details:

• The complete instrument is light weight and is supplied in two parts for easy assembling and disassembling on site with help of hand tools and also it becomes easy to carry with the help of handle.
• In use one end of the beam rests at a point under investigation while the beam is pivoted at the centre. The free end carries a dial gauge to record the deflections and the other end is kept on the a stable platform. Because of beam ratio small deflection is magnified and recorded on the dial gauge.
• In use one end of the beam rests at a point under investigation while the beam is pivoted at the centre. The free end carries a dial gauge to record the deflections and the other end is kept on the a stable platform. Because of beam ratio small deflection is magnified and recorded on the dial gauge

Note - Price will be change as per specification

Product Details:

Application

This is used for a quantitative determination of bitumen in hot mix paving mixtures and pavement samples.

 Construction Details

• Safe & Portable model of sufficient size for quick and accurate determination of bitumen.
• Corrosion-resistant model which can be used both in  the field and the laboratory.
• Consists of a removable cast aluminum rotor bowl mounted on a vertical shaft.
• A filter paper disc is pressed in between the nut.
• The bowl assembly is enclosed in a housing mounted on a cast aluminum body.
• The gears operate in oil bath with splash lubrication.
• Special model with Flameproof Motor, DC-Motor drive and Electronic speed control and Digital RPM Indicator

 Salient Features

• Flameproof Motor
• Electronic Speed Control
• Facilitates precise speed control
• Offers Vibration free smooth operation
• With a brake control for rapid deceleration
• Internal wiring as per CE Standards
• Safety label as per CE Norms
• Bowl Capacity      :  1500 grams
• Variable speed    :  50-3600 RPM
• Power Supply      :  220 Volt, 50-60 Hz, Single Phase, AC Supply
• Removable Aluminum integral cup for adding solvent
• All parts of the body are seamlessly argon welded
• Essential parts of the instrument are hard chrome plated
• Digital RPM Indicator continuously display the RPM on screen

Note - Price will be change as per specification

Product Details:

Apparatus For Determination Of Mineral Matter - AS Per : 1217

We Are Manufacturer Of 

• Apparatus For Det. Of Matter Insoluble In Toluene - As Per  1215

• Apparatus For Determination Of Napthalene In Tar & Bitumen - As Per Is : 1219

• Apparatus For Determination Of Phenol-Is 1218

Note - Price will be change as per specification

 

Product Details:

Tensile splitting device(Lottman breaking head) for 100 mm And 150 mm dia compacted bituminous samples. (ASTM D6931) FOR 4" And 6" DIA MARSHAL SPECIMEN. COMPLETE WITH LOADING STRIPS. The fixture Breaking head assembly with Guide rods and loading strips will be supplied. The Marshal Machine, water bath, Oven etc. required for test will not be part of this supply.

Note - Price will be change as per specification

Product Details:

Complies with following International Standards - ASTM D6927, ASTM D1559. Application - It is used to measure the resistance to plastic flow of cylindrical specimens of bituminous mixture loaded on the lateral surface.

Also We Have Marshal Stability Testing Machine Modified-6 Inches Dia-With Proving Ring And Dial Gauge

Note - Price will be change as per specification

 

Product Details:

Ductility is defined as distance in cms to which a standard briquette of bitumen can be stretched before the thread breaks. The briquette is stretched at a rate of 50 mm/min.± 2.5mm per minute at a temperature of 27°C ± 0.5°C

 The Machine is having built in refrigeration system to work a below ambient temperature up to 10°C in tropical conditions. The Machine will operate at 27°C with control accuracy of ± 0.5°C as per the requirement of IS.

Note - Price will be change as per specification

Product Details:

Introduction:

Used for specific gravity test by removing air voids from the Bitumen Mix. Very useful for other general laboratory tests where vacuum is required.

Specifications:

Complete with base, motor, pulley and belt. The pump mechanism is contained in a metal case with oil level and drain plug at base. Pump speed 450 RPM. Ultimate vacuum 0.01 mm/Hg. (Single stage). Complete with non-return valve, belt gauge and vacuum gauge with regulator.

Displacement:

50 Ltr./Min, Motor Rating : 0.25 HP Single Phase. To work on 230 V AC, 50 Hz. Single Phase. Supplied complete with filtering flask of 1000 / 2000 ml. Capacity with rubber cork and pressure pipe to carry out the test.

Optional Accessories:

• Air Ballast.
• Moisture Trap
• Hard Rubber Pipe of Required Length.

Note - Price will be change as per specification

Product Details:

Introduction:

• This method is used for determining the ductility of bituminous materials by measuring the elongation before breaking when two ends of a briquette specimen are pulled apart at a speed of 50 mm/min 2.5 mm/min at temperature of 270 C 0.50 C.

Other Details:

• Stainless steel bath
• Temperature controller (Thermostatic/Digital)
• Immersion electric heater
• Constant speed Pump cum stirrer
• Carriage holding up to three standard briquette moulds
• Electric motor with gear mechanism
• Stainless steel scale and pointer
• Control Panel

Specifications:

• The apparatus consists of water bath with a thermostatic heater and a circulating pump to maintain uniform water temperature.
• One half of the briquette moulds is fixed in a fixed plate in the water bath, the other half of the briquette mould is fixed to a carrier which slides over a rotating threaded shaft with a clutch.
• The motor and gears to rotate the shaft are housed in a cabinet fixed above the other end of the both. A pointer fixed to the carrier moves over. a scale graduated from 0-110 cm x 1mm fixed on the bath with "0" (Zero) of the scale towards the fixed plates side.
• The rotating shaft has 2 speeds of travel for the bracket, 5 cm/min. and 1cm/min. selected by a clutch. Water bath inside is of Stainless steel with insulation and a water drain. A heater with thermostatic control is fitted. inside the water bath.
• Control switches for motor, stirrer, heater and indicator lamps are fitted to a control panel located at a convenient place on the water bath. Complete with three briquette moulds and one base plate. Working on 230 Volts, single phase, 50 cycles, AC.

Optional Fittings At Extra Cost:

• Digital Temperature indicator cum controller (in place of Thermostatic control)
• Digital display for Elongation
• The more advanced model with refrigeration system which ensures better temperature control in tropical conditions. The Machine is mounted on a steel stand with refrigeration unit at its base.
• Base Plate for mould.
• Mould for elastic recovery.

Note - Price will be change as per specification

Product Details:

Introduction:

A depression made in the sample by a needle weight which is measured in tenths of a millimeter and expressed, as penetration number. A standard needle penetrated vertically under surcharge weight 50 gm into a sample under test temperature at 25°C for 5 second of duration. This test determine the consistency and thereby the grade of the bitumen.

General Description & Specification:

• The apparatus is available in two versions, hand operated and electrically operated with automatic timer. The apparatus consist of a cast aluminum base with an iron stand on which moves an aluminum arm. A 6” dial is fixed on this arm and a brass chromium plated rod slide through the lower portion of the arm. A needle with weight is fitted to this rod. The dial is graduated from 0-400 in one tenth millimeter sub division. Supplied complete with adjustable needle holder, penetration needle, sample container, transfer dish and weight of 50 gm.
• The automatic model is supplied with automatic digital timer and electrical arrangement to carryout the test without need of stop watch and with great ease and accuracy.
• Automatic penetro meter with LVDT and auto timer can be supplied with indication of time and penetration in digital mode.

Optional accessories:
The following accessories and consumables are not part of the standard supply and are supplied at extra cost

• Constant temperature water bath EIE 403/ 406.
• Glass thermometer,
• Electric hot plate.
• Spare bitumen container 55 mm x 35 mm
• Spare container 70 mm x 45 mm.
• Enamel tray.
• Stop watch mechanical/ digital.
• Spare penetration needle.
• Spare weight 50 gm.

Note:

The above instrument with some modification can also be used for testing 0f Grease/soil/food products and other similar matetials for penetration test. The brass cone is used in place of needle for penetration. Variety 0f accessories are available for diftefent appications. Prices and details are provided on request.

Advanced Standard Penetrometer: 

• same as about but with Digital display of Penetration Value with bulit in timer.
• Lifting table with adjustable mechanism  for initial precise setting.
• with rack and pinion movement to fix an aluminum arm at desired position 

 Price will be change as per specification

Additional Information:

• Item Code: EIE-TM-044

Product Details:

As per IP???49 and IS???1448. This apparatus is used for penetration test on a wide variety of materials such as grease, petroleum, Bitumen, Tar, Wax, olish, foodstuff, rubber asphalts and Pharmaceutical creams. A depression is made in the sample by a needle of a definite weights which is measured intents of a millimeter and expressed as penetration number. Detailed specification as follows:

Note : Price will be change as per specification

Product Details:

We are manufacturer of Automatic Compactor for Marshal Test. It is a motor driven mechanical compactor useful for soil compaction into 100 mm or 150 mm diameter moulds. Two sets of rammers are provided, one of 2.6 and arranged for 310 mm. drop and other 4.9 kg and arranged for 450 mm fall. for comaction soil into 150 mm dia moulds, 100 mm face dia rammers having weight 2.6 kg and 489 kg are used. Where as for 100 mm dia moulds they are of 50 mm dia. The rammer assembly is provided with a ratched and pawl arrangement to lift it from the top of the soil layer. When the rammer reaches the required height the pawl release the rammer which falls freely on soil surface. The release mechanism is operated by an arm moving up and down which is connected to a reduction gear coupled to the motor through another arm. An automatic blow counter fitted to the compactor is used to set the number of blows. The base plate of the specimen mould is to be fitted to the rotating base plate of the instrument which makes 1/5th revolution per stroke. The equipment is suitable for operation on 230 volts, 50 cycles, single phase, A.C. supply. Mould are to be ordered separately.

Also we have manufacturer-

AUTOMATIC COMPACTOR FOR MARSHAL TEST - 4" DIA SPECIMEN

AUTOMATIC COMPACTOR FOR MARSHAL TEST - 6" DIA SPECIMEN

Note - Price will be change as per specification

Product Details:

Introduction

Planetary Mixer is used in Bitumen Testing Laboratories to speed up the process of preparing cylindrical specimens for Marshal Stability Test. The mix is uniformly heated and mixed to yield homogenous mix of better moulds for testing. The same mixer with heating jacket and some modifications can also be used for mixing of soil, cement paste, mortars, pozzolanas etc.

Salient Features

• Electrically operated
• Fitted with heating jacket, Stainless Steel paddle and Electric Motor for thorough mixing of Bitumen.
• Electric Motor is connected to epicyclical type stainless steel paddles to impart both planetary and revolving motion for uniform mixing.
• The mixer has three different speeds for mixing i.e. low, medium and high.
• Mixer blade has low speed of 140 ± 5 rpm and medium speed of 285 ± 10 rpm, while it also has a planetary movement of 62 ± 5 rpm in low range and planetary movement of  125 ± 10 rpm in medium range.
• Stainless Steel paddle is fitted inside the stainless steel bowl of approximately 5 liter capacity with handle.
• The 500 Watts heating jacket with energy regulator to control the temperature of mixture is fitted below the bowl.
• Thermostat controlled temperature
• Complete unit is supported on a strong iron frame.
• External body of the unit is powder coated in attractive shades.
• Suitable to work on 230-220 Volt, 50 Hz, Single phase, AC Supply
• Weight: 32 kg

Note - Price will be change as per specification

Product Details:

Specifications:

• Often, existing concrete structures will need to be examined and tested to ensure the concrete remains of adequate strength and durability. This test is used to determine the compressive strength of a concrete core, which has usually been extracted from an existing structure. The value of compressive strength can then be used in conjunction with other measured properties to assess the condition of the concrete.
• Extraction of concrete cores, achieved by rotary drilling using a diamond tipped hollow barrel, serve as a means of taking a sample of concrete which can then be used to determine various physical properties, but most commonly compressive strength.
• Cores can generally be extracted from wherever access allows, and would include floor slabs, walls and columns. 10cm diameter cores, generally afford the minimum diameter required for a representative sample and require less reinstatement than larger diameter cores. 15cm diameter cores will generally give more representative samples than smaller diameters but require more reinstatement.

Note - Price will be change as per specification

Product Details:

As per IP 27, IS 1213 ASTM D402 method A complete with one distillation flask of 500ml. capacity and one 100 ml. crow receiver (without thermometer) Electrically heated model with Energy regulator.

Note : Price will be change as per specification.

Additional Information:

• Item Code: EIE-BT-107
• Production Capacity: 100 Per annum
• Delivery Time: 3-4 Weeks after receipt of confirmed order
• Packaging Details: Wooden packing with strong base.